Owner Resources

Insulation Blowing Machine for Sale or Rent: What to Check

A worker taping a duct joint in an attic where metal ducts run across a floor of yellow fiberglass

To buy or rent an insulation blowing machine with care, read it against its owner’s manual, search the seller’s name for a lien, learn whether the warranty follows the machine, and line up the money. Then insure it: the machine as contractors equipment, and the commercial auto policy told about the truck or trailer that carries it.

What you inspect first depends on how the machine reaches you

Each path changes what you inspect and who stands behind the machine. On a new machine, the delivery is where inspection starts: a truck-mounted model’s manual says the machine “should be received in the same condition that it was shipped to you.”, and it tells the owner to place any claim for visible problems with the delivery carrier.

On a used machine, the warranty may stay behind. A blowing-machine manufacturer’s warranty says “This warranty is non-transferable.”, and the truck-mount maker’s warranty runs “to each original purchaser (Buyer) of its machines”. A used buyer pays for condition, so the next sections matter more on that path. On a rented machine, the open question is insurance, which the policy section below takes up. If you are still building the business around the machine, our guide to starting an insulation business puts the purchase in order with the license, the crew and the coverage.

Reading a used blower against its maintenance schedule

The manual tells you what wears, so ask the seller for it and inspect those parts. A blowing-machine manufacturer’s owner’s manual lists daily checks for clogged filters and “Insulation build up on motors and electrical components.” Its weekly check says “The belt should not be frayed or slipping on the pulleys.” Its monthly checks cover the airlock seals, tested with a pressure gauge, and chain tension, and it says “Do not lubricate chain”.

The same manual says “Replace all of your airlock seals as soon as a decrease in production occurs.”, and that seal life depends in part on the material: “the more abrasive the material, the shorter the seal life”. It also says to “promptly replace worn agitator paddles, because worn paddles will also reduce machine production.” Ask when the seals and paddles were last changed, what material the machine has been blowing, and whether a written service history exists.

OSHA’s construction rules on guarding, hearing protection and ground-fault protection

Federal OSHA’s construction standards bind employers whose crews work on construction sites, and they speak of tools and equipment in general terms. The construction standard on hand and power tools says “All hand and power tools and similar equipment, whether furnished by the employer or the employee, shall be maintained in a safe condition.” It also says “Belts, gears, shafts, pulleys, sprockets, spindles, drums, fly wheels, chains, or other reciprocating, rotating or moving parts of equipment shall be guarded if such parts are exposed to contact by employees or otherwise create a hazard.” The truck-mount manual says “Operate your machine according to the outlined instructions in the manual with all guards in place and securely latched.” OSHA’s general construction provisions add “The employer shall permit only those employees qualified by training or experience to operate equipment and machinery.”

The truck-mount manual raises noise and electrical power too. A decal in the truck-mount manual says “During operation, this machine is loud. Wear hearing protection. Failure to do this could result in hearing loss.” OSHA’s construction hearing protection rule says that where it is not feasible to reduce the noise levels or the duration of exposures to its table’s limits, “ear protective devices shall be provided and used.” Its construction electrical standard requires the employer, for the outlets its later paragraphs describe, to use ground fault circuit interrupters or an assured equipment grounding conductor program “to protect employees on construction sites.”, and the truck-mount manual says “Use a ground fault circuit interrupter (GFCI) in any damp or highly conductive area.”

Liens: searching the seller’s name before you pay

A used machine can carry a lender’s claim, so search the seller’s name with the state filing office before money changes hands. The Montana Secretary of State says “A UCC lien is a financial document stating that a lender (secured party) has a claim in certain property belonging to someone else (debtor).” and “A lien filed with the Secretary of State provides notice to interested parties of the existence of a security interest against specific collateral.” Its online search “allows users to search debtor names, view filing chains, and download debtor search certificates and images of lien documents.” The Texas Secretary of State says “UCC searches and orders are done online through the SOSPortal on the Search and Orders page.”

Minnesota’s commercial code shows why the search can matter. The Minnesota statute says that, except as otherwise provided, “a security interest or agricultural lien continues in collateral notwithstanding sale, lease, license, exchange, or other disposition thereof unless the secured party authorized the disposition free of the security interest or agricultural lien”. Minnesota’s code also says, subject to its own exceptions, that “a buyer in ordinary course of business, other than a person buying farm products from a person engaged in farming operations, takes free of a security interest created by the buyer’s seller, even if the security interest is perfected and the buyer knows of its existence.”

That protection turns on the seller. The same code defines a buyer in ordinary course of business as “a person that buys goods in good faith, without knowledge that the sale violates the rights of another person in the goods, and in the ordinary course from a person, other than a pawnbroker, in the business of selling goods of that kind.” Whether your purchase fits those words under your own state’s code is a question for a lawyer. If the search finds a filing that names the seller, get the lender’s written release before you pay.

Real-World Scenario: A contractor who is closing his shop lists a used truck-mounted blower, and a cellulose installer wants it. Before agreeing to terms, she searches the seller’s name with the state filing office and finds a financing statement filed by a lender. She has the seller get that lender’s release, checks the airlock seals, belts and guards against the manual, writes down the serial numbers, and phones her insurance agent to schedule the machine and add the truck before she drives it home.

Warranty, serial numbers and the papers that follow the machine

The papers decide what you can claim later, so collect them at the sale. A blowing-machine manufacturer’s warranty says “The warranty applies to products in normal use only.” and that the product “must be serviced and maintained as described therein”, and it excludes seals, filters, belts, paddles and relays as normal wear items unless the manufacturer finds them defective. The truck-mount maker’s warranty excludes “Any machine that has not been operated and/or maintained in accordance with normal industry practice and the written recommendations of the Company.”

Write down every serial number on the day the machine arrives. The truck-mount manual asks the owner to fill in the model and serial numbers of the machine, its engine and its blower “For your protection in the event of theft or loss”, and it says “You may also want to attach a copy of your invoice.”

Paying for it: SBA-backed loans and lenders

A blowing machine can be a listed use for a loan the SBA backs, but you work with a lender, not with the SBA. The U.S. Small Business Administration says “The 7(a) loan program, SBA’s primary business loan program, provides a loan guarantee to lenders that allow them to provide financial help for small businesses with special requirements.” Its list of uses includes “Purchasing and installation of machinery and equipment”. It also says “You will always work directly with your lender and not with SBA.”, and among its eligibility conditions a business must “Be creditworthy and demonstrate a reasonable ability to repay the loan”.

The SBA’s microloan page lists “Machinery” and “Equipment” among its examples of uses and says “SBA-approved lenders make all credit decisions and set all terms for your microloan.” Ask any lender what it wants to see on the machine itself, such as the serial numbers, the invoice and proof of insurance.

What the bag label and your receipt say about the machine

The FTC’s rule on labeling home insulation ties a loose-fill bag to the machine that blows it. It describes insulation that “may be in rigid, semirigid, flexible, or loose-fill form.” For loose-fill products, the label chart shows “the minimum settled thickness, initial installed thickness, maximum net coverage area”, among other items, and the FTC rule tells the manufacturer “You must also provide information about the blowing machine and machine settings used to derive the initial installed thickness information.”

The receipt is the installer’s part when the job is home insulation. The rule says “If you are an installer, you must give your customers a contract or receipt for the insulation you install.” For loose-fill work, “the receipt must show the coverage area, initial installed thickness, minimum settled thickness, R-value, and the number of bags used.” It also says “The receipt must be dated and signed by the installer.” Our licensing guide covers that receipt duty too.

Cellulose bags carry a federal label of their own. The Consumer Product Safety Commission’s cellulose insulation rule says “Manufacturers of cellulose insulation shall label all containers of cellulose insulation with the following statement”, and under the heading “Request to Installer” that label reads “Remove this label and give it to the consumer at completion of job.” The fiberglass and blown-in insurance page reads the exposures of that work.

Insuring the machine as contractors equipment

A blowing machine is equipment, and the contractors equipment form we read covers what it describes. It says “We cover only those described items for which a coverage amount is shown.” and “It is a condition that at the time this coverage is effective all described items are in sound condition.” It says “A coverage amount must be shown for each item. This is the most that we will pay for a loss to that item.”

The same form leaves wear to you. It does not cover “mechanical breakdown or failure”, though “If a fire or explosion results, we do cover the loss caused by the fire or explosion”, and it excludes loss caused by “wear and tear, gradual deterioration”.

A rented machine needs its own look. Under the ISO businessowners tools endorsement, its owned-tools coverage leaves out “Non-owned tools and equipment leased or rented from others that are in your care, custody or control”, with an exception for leases of the length the form sets, and a separate optional coverage, with its own limit in the schedule, takes in rented tools and equipment, apart from loss the form carves out, theft among them. Insurers file their own versions of these forms, and the inland marine and equipment page reads them.

The truck or trailer it rides in

The vehicle is an auto policy question, and how the machine is mounted shapes it. The truck-mount manual says the machine “is designed to be mounted in the van body of the contractor’s truck”. In the ISO business auto form, “Auto” means “A land motor vehicle, ‘trailer’ or semitrailer designed for travel on public roads”, among other vehicles, and the definition carves out mobile equipment.

The form sorts vehicles by what is permanently attached. A self-propelled vehicle maintained primarily for purposes other than carrying people or cargo, with permanently attached “Air compressors, pumps and generators”, is not mobile equipment and “will be considered” an auto. A trailer or similar vehicle that cannot drive itself, and that exists mainly to carry such attached equipment, falls within the mobile equipment definition, unless a state law on insuring motor vehicles reaches it where it is licensed or mainly garaged. The form names those kinds of equipment, not a blowing machine, so the policy wording and the state’s law decide how your truck or trailer is treated.

Minnesota’s Department of Commerce tells small businesses “Consider increasing insurance on your business vehicle to cover permanently attached items, such as a generator or storage unit.” The auto form’s physical damage coverage will not pay for loss “due and confined to” “Wear and tear, freezing, mechanical or electrical breakdown”, except for loss from the total theft of the vehicle. The commercial auto page walks through that form, and our post on a spray foam rig for sale takes up the same vehicle question for a proportioner rig.

Once the machine and its insurer are settled, send their details through the quote form. For the rest of the operation, see the insulation business insurance overview, and workers’ compensation belongs there for the crew that runs the machine.

Bringing a blowing machine into a blown-in business, from the purchase choice to the policies that carry it

Steps for a crew bringing in a blowing machine. Decide on a new machine, a used machine or a rental. Read the machine against its owner’s manual: filters, belts, chain, airlock seals and paddles. Search the seller’s name with the state filing office for a lien on the machine. Arrange the money with a lender. Keep the warranty terms, the serial numbers and the invoice. Put the machine on a contractors equipment policy. Tell the commercial auto policy about the truck or trailer that carries it. No figures are shown.

Frequently asked questions

Insulation blowing machine for sale: what do you inspect before paying?

Check the wear parts a maker’s manual names: filters, belts, chain, airlock seals and agitator paddles. A manual we read says “Replace all of your airlock seals as soon as a decrease in production occurs.” Search the seller’s name for a lien, because Minnesota’s commercial code says that, except as otherwise provided, a security interest “continues in collateral notwithstanding sale” unless the secured party authorized the sale free of it. An equipment form we read also makes it a condition that described items are “in sound condition” when coverage starts.

Insulation blower machine for sale used: is there a lien on it?

Run a UCC search on the seller’s name with the state filing office. Montana’s office says “A lien filed with the Secretary of State provides notice to interested parties of the existence of a security interest against specific collateral.” Its online search lets users “search debtor names, view filing chains, and download debtor search certificates”, and the Texas office says “UCC searches and orders are done online through the SOSPortal on the Search and Orders page.” Ask for a lender’s release before you pay.

Insulation blowing machine rental: is a rented machine on your equipment policy?

It may not be. Under the ISO businessowners tools endorsement, the owned-tools coverage leaves out “Non-owned tools and equipment leased or rented from others that are in your care, custody or control”, with an exception for leases of the length the form sets. A separate optional coverage, with its own limit in the schedule, takes in rented tools and equipment, apart from loss the form carves out, theft among them. Insurers file their own versions of the endorsement, so read your policy’s wording and its schedule before the rental leaves the counter.

Insulation blowing machine repair: does an equipment policy pay for a breakdown?

The contractors equipment form we read does not cover “mechanical breakdown or failure”, though “If a fire or explosion results, we do cover the loss caused by the fire or explosion”. It also excludes loss from “wear and tear, gradual deterioration”. The ISO business auto form has a matching line for the vehicle: its physical damage coverage will not pay for loss “due and confined to” wear and tear or breakdown, except on total theft. Plan wear repairs as part of maintaining the machine.

Cellulose insulation blowing machine for sale: what do the bag labels ask of the installer?

The Consumer Product Safety Commission’s cellulose rule has manufacturers put a caution on every container, and under the heading “Request to Installer” it reads “Remove this label and give it to the consumer at completion of job.” The same label asks that the insulation be kept away from “exhaust flues of furnaces, water heaters, space heaters, or other heat-producing devices.” Under the FTC’s home insulation rule, a loose-fill receipt shows “the coverage area, initial installed thickness, minimum settled thickness, R-value, and the number of bags used.”

Blown insulation machine for sale: will an SBA-backed loan cover the purchase?

The purchase can fit a listed use. The SBA’s page on its primary business loan program lists “Purchasing and installation of machinery and equipment”, and its microloan page lists “Machinery” and “Equipment” among example uses. You deal with a lender: the SBA says “You will always work directly with your lender and not with SBA.”, a business must “Be creditworthy and demonstrate a reasonable ability to repay the loan”, and for microloans “SBA-approved lenders make all credit decisions and set all terms”.

Attic insulation blowing machine for sale: what does OSHA expect of it on a job site?

OSHA’s construction standard on hand and power tools says tools “and similar equipment, whether furnished by the employer or the employee, shall be maintained in a safe condition.” It requires belts, chains, pulleys and other moving parts to be guarded “if such parts are exposed to contact by employees or otherwise create a hazard.” Its general provisions add “The employer shall permit only those employees qualified by training or experience to operate equipment and machinery.” These are federal OSHA rules for employers in construction.