States we serve

Ohio Insulation Contractor Insurance

In Ohio, ORC 4123.82(A) voids contracts that “undertake to indemnify or insure an employer against loss or liability for the payment of compensation”, with the exceptions the section lists, and employers pay premium into the state insurance fund unless the administrator grants them status as a self-insuring employer under ORC 4123.35(B). The licensed-trade list in ORC 4740.01(D) names no insulation category.

Get a Quote Call 317-942-0549

A worker in a hard hat pressing fiberglass batts into the wall framing of a gable-end attic — insulation contractor insurance in Ohio

In Ohio, ORC 4123.35(A) has “every private employer and every publicly owned utility” pay premium “into the state insurance fund”, except as that section otherwise provides, and ORC 4123.82(A) voids contracts that “undertake to indemnify or insure an employer against loss or liability for the payment of compensation”, with the exceptions section 4123.82 lists; beside the fund, the administrator may grant self-insurance under ORC 4123.35(B). ORC 4740.01(D) defines the trades the Ohio Construction Industry Licensing Board licenses, a list that names no insulation category. Local registration, liability certificates and proof of workers’ compensation appear on the cards below.

ORC 4740.01(D)’s licensed trades, the residential-building carve-out in ORC 4740.01(F) and OCILB’s complaint form

ORC 4740.01(D) defines a “Licensed trade” as “a trade performed by a heating, ventilating, and air conditioning contractor, a refrigeration contractor, an electrical contractor, a plumbing contractor, or a hydronics contractor.” That list names no insulation category. The board’s chapter reaches a “Construction project” as ORC 4740.01(F) defines it — a project on a building subject to Chapter 3781, “but not an industrialized unit or a residential building as defined in section 3781.06 of the Revised Code.”

The board’s contractor complaint form says it “licenses commercial contractors in five trades” and that “OCILB may not have authority over residential contractors.” For the trades the board licenses, ORC 4740.06(B) says that, to qualify to take an examination, an individual shall “Maintain contractor’s liability insurance in an amount the appropriate specialty section of the board determines and only in one contracting company name”.

ORC 4123.82(A), the state insurance fund and the Greenbook’s “sole insurance provider”

ORC 4123.82(A) says “All contracts and agreements are void which undertake to indemnify or insure an employer against loss or liability for the payment of compensation to workers or their dependents for death, injury, or occupational disease occasioned in the course of the workers’ employment”, and “No license or authority to enter into any such agreements or issue any such policies of insurance shall be granted or issued by any public authority in this state.” Under ORC 4123.35(A), except as that section otherwise provides, “every private employer and every publicly owned utility shall pay annually in the month of June immediately preceding the policy year into the state insurance fund the amount of estimated annual premium the administrator fixes for the employment or occupation of the employer”. The Legislative Service Commission’s Greenbook on the Bureau of Workers’ Compensation, a budget analysis, says “An exclusive workers’ compensation system is a system in which the state is the sole insurance provider, not private insurers.” The same Greenbook says the bureau “provides workers’ compensation insurance to all public and private employers in Ohio, except for certain companies that have sufficient financial and administrative resources and thus qualify for self-insurance programs.”

Self-insurance sits beside the state insurance fund: under Ohio Revised Code section 4123.35(B), employers “who may be of sufficient financial ability to render certain the payment of compensation to injured employees or the dependents of killed employees” and “who do not desire to insure the payment thereof” may, on the administrator’s finding, be granted the privilege to pay compensation directly, “thereby being granted status as a self-insuring employer.” ORC 4121.121(A) says “There is hereby created the bureau of workers’ compensation, which shall be administered by the administrator of workers’ compensation.” Under ORC 4123.30, the state insurance fund’s separate funds and the net premiums paid into them, apart from the amounts the section sets aside, “constitute a trust fund for the benefit of employers and employees”.

A subcontractor’s unpaid premium, the bureau’s posted notice and a sole proprietor’s election under ORC 4123.01

For an insulation subcontract, ORC 4123.35(A) says “A private employer who has contracted with a subcontractor is liable for the unpaid premium due from any subcontractor with respect to that part of the payroll of the subcontractor that is for work performed pursuant to the contract with the employer.” ORC 4123.01 lets a partnership or sole proprietorship elect to include as an employee “any member of such partnership, the owner of the sole proprietorship, the individual incorporated as a corporation, or the officers of the family farm corporation.”, an election that takes written notice to the bureau.

ORC 4123.83 has each employer paying premiums into the state insurance fund, or electing directly to pay compensation under section 4123.35, post the bureau’s notice “conspicuously in the employer’s place or places of employment or on the internet in a manner that is accessible to the employer’s employees”, and says “The notice shall indicate that coverage is contingent on continued payment of premiums and assessments due.” ORC 4123.77 says private employers who fail to comply with section 4123.35 lose the benefits of the chapter’s sections during the period of such noncompliance and are liable to their employees “for damages suffered by reason of personal injuries sustained in the course of employment caused by the wrongful act, neglect, or default of the employer”. Those sections bear on workers’ compensation in Ohio.

The Board of Building Standards’ separate residential and nonresidential codes under ORC 3781.10

ORC 3781.10(A)(1) says “The board shall incorporate those rules into separate residential and nonresidential building codes. The standards shall relate to the conservation of energy and the safety and sanitation of those buildings.” OAC 4101:8-1-01 takes The 2018 edition of the “International Residential Code” as the basis of the Residential Code of Ohio, and its section 101.2 says “The provisions of the "Residential Code of Ohio for One-, Two-, and Three-Family Dwellings" shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal, and demolition of every one-, two-, or three-family dwelling”. The Ohio Building Code takes the International Building Code 2021 edition as its basis under OAC 4101:1-1-01.

Under ORC 3781.10(A)(2)(b), “The rules governing residential buildings are uniform requirements in any area with a building department certified to enforce the state residential building code in accordance with division (E) of this section, for both of the following”: “The erection and construction of new residential buildings” and “The repair and alteration of existing residential buildings.” Where no certified department has jurisdiction, section 101.5 of OAC 4101:8-1-01 says “If no municipal, township, or county building department is certified by the Board of Building Standards for residential buildings in accordance with section 3781.10(E) of the Revised Code has jurisdiction, the owner is not required to make submission of construction documents, seek approvals, request inspections, or obtain certificates of occupancy required in this Chapter.”

The Residential Code of Ohio’s OHBA alternative and the Ohio Building Code’s IECC-or-ASHRAE rule

The Residential Code of Ohio’s energy chapter, OAC 4101:8-11-01, says “Compliance shall be demonstrated by meeting the requirements of one of the following options:” and lists among those options “Section 1112 (“The Ohio Home Builder’s Association (OHBA) Alternative Energy Code Option”)” and “The "International Energy Conservation Code."” Its referenced-standards rule, OAC 4101:8-44-01, lists “IECC—18: International Energy Conservation Code”, and the Ohio Laws page for the energy chapter prints “Effective: July 1, 2019”.

For buildings under the Ohio Building Code, its energy chapter, OAC 4101:1-13-01, says “Buildings are to be designed and constructed in accordance with the applicable provisions of the "International Energy Conservation Code" or the requirements of "ASHRAE 90.1" listed in Chapter 35 of this code except as modified in Sections 1301.2 and 1301.3.” Its referenced-standards rule, OAC 4101:1-35-01, lists “IECC - 21 International Energy Conservation Code” and “90.1-19 Energy Standard for Buildings Except”, and the Ohio Laws page for that chapter prints “Effective: October 15, 2025”.

Section 1101.10.1 installer certifications, attic depth markers and the section 1102.2.4 loose-fill baffle

Under section 1101.10.1 of the Residential Code of Ohio, an R-value identification mark is applied by the manufacturer to each piece of building thermal envelope insulation that is at or above a width the section states. “Alternatively, the insulation installers shall provide a certification that indicates the type, manufacturer and R-value of insulation installed in each element of” the building thermal envelope. For spray foam work, the section says “For sprayed polyurethane foam (SPF) insulation, the installed thickness of the areas covered and the R-value of the installed thickness shall be indicated on the certification.” For blown-in or sprayed fiberglass and cellulose insulation, it has the certification show the initial installed thickness, settled thickness, settled R-value, installed density, coverage area and number of bags installed. Of the certification as a whole, it says “The insulation installer shall sign, date and post the certification in a conspicuous location on the job site.” Its exception for roof insulation installed above the deck says the R-value “shall be labeled as required by the material standards specified in Table 906.2.”

Section 1101.10.1.1 requires that the thickness of blown-in or sprayed fiberglass and cellulose roof and ceiling insulation “be written in inches (mm) on markers” installed throughout the attic space at the spacing it sets, and “Each marker shall face the attic access opening.” Section 1102.2.4 says “Where loose-fill insulation is installed, a wood-framed or equivalent baffle or retainer shall be installed to prevent the loose-fill insulation from spilling into the living space when the attic access is opened.”

Respiratory protection on construction work under 29 CFR 1926.103, with requirements identical to 29 CFR 1910.134

OSHA’s State Plans page lists Ohio as “OH” with no asterisk, where an asterisk marks a State Plan that covers private as well as state and local government workplaces. OSHA’s construction standard 29 CFR 1926.103, on respiratory protection, says “The requirements applicable to construction work under this section are identical to those set forth at 29 CFR 1910.134 of this chapter.”

For spray foam contractors, the U.S. Consumer Product Safety Commission’s fact sheet says the high-pressure and low-pressure products it describes “contain isocyanates in Side A”. The EPA checklist on contractor-client communications for high-pressure spray polyurethane foam describes itself as “a voluntary aid to protect against potential risks from SPF” and “not a regulatory compliance tool”. Nationally, the Federal Trade Commission’s R-value rule, 16 CFR 460.17, tells installers “you must give your customers a contract or receipt for the insulation you install”. The EPA’s vermiculite page says “If you have vermiculite insulation in your home, you should assume this material may be contaminated with asbestos”.

Columbus’s home improvement board, Cincinnati’s OBWC proof line and Olmsted Township’s additional insured

The cards below quote each Ohio office’s own page or application. Columbus says a contractor who wishes “to perform structural work on existing” dwellings of the kinds the city lists must be licensed as a City of Columbus home improvement contractor, and that applications “are reviewed by the Board of General and Home Improvement Contractors.”

Columbus

The Department of Building and Zoning Services says “All contractors performing work within the city are required to obtain the appropriate license or registration before they can apply for permits and begin the job.” For a general contractor registration, the city asks for a notarized application, a bond on the city’s form and a Certificate of Liability Insurance naming the department as certificate holder, “written by an insurance company licensed to do business in the State of Ohio.”

Cleveland

The City of Cleveland’s Building & Housing contractor permits page says “To build or rehabilitate Cleveland homes, contractors must be bonded, insured, and registered.” It adds: “Owner-occupants of one- or two-family homes may perform alterations or build homes without being registered as contractors, but are subject to the same regulations that apply to contractors for permits, plan examination, and inspection.”

Cincinnati

Cincinnati’s Department of Buildings & Inspections says “Liability insurance is a requirement of all registrants and proof of such will be required at the time of registration.” Its registration rules call for a “Certificate of Liability Insurance” that “shall be written by an insurance company licensed to do business in the State of Ohio” at the minimum limits its FAQ states, and “Proof of Ohio Workers’ Compensation coverage.” The FAQ excuses from that proof, at the time of registration, “Those sole proprietors and business entities with no employees that are not required by state law to carry OBWC coverage”.

Akron

The City of Akron’s Plans and Permits page says “The City of Akron requires all contractors regardless of trade to register as a contractor if the work they are preforming requires a permit to do the work.” A registration takes an application, an Akron tax registration number, a “Certificate of Liability Insurance”, state licenses where the line “Only applies if you have or are required to have for your trade”, and a “Copy of Workmen’s Compensation”, which “Contractors without employees do not require”.

Franklin County

For its unincorporated area, the Franklin County Development Department’s Building FAQ says “You do not need a Contractor’s License to obtain a structural building permit to work in unincorporated Franklin County, however to perform electrical, heating, or plumbing work you must possess a valid license.” It adds “A homeowner, contractor, or individual acting as the owner’s agent may apply for a building permit.”

Olmsted Township

Olmsted Township requires contractor registration each calendar year, a bond on its own form, and “A Certificate of Insurance showing Olmsted Township as Certificate Holder and additional insured” at the per-occurrence and aggregate amounts its page states, including products-completed operations. The township’s Contractor Registration page also says “Permits must be obtained and posted at job site before work begins.”

Sources: City of Columbus Contractor Licenses, City of Cleveland Contractor Permits, Cincinnati Contractor Registration FAQ, City of Akron Plans and Permits, Franklin County Development Department Building FAQs and Olmsted Township Contractor Registration.

Premium into the state insurance fund under division (A) of ORC 4123.35, or self-insuring status under division (B)

Workers’ compensation in Ohio follows ORC 4123.35: under division (A), except as the section otherwise provides, a private employer pays premium “into the state insurance fund”, and under division (B) an employer the administrator finds of sufficient financial ability may be granted “status as a self-insuring employer.” Lines a quote can take up include general liability, commercial auto, inland marine for tools and equipment, umbrella liability and commercial property. An Ohio crew that sprays foam can start at spray foam insurance, a crew that blows or batts glass at fiberglass insulation contractor insurance, and any installer at the insulation business insurance page.

Through Wexford Insurance, LLC, an independent insurance agency, Insulation Contractor Insurance places coverage for insulation contractors. Premium depends on payroll, the materials you spray or blow, subcontracted work, vehicles and rigs, tool and equipment values, and the states you work in. We do not publish typical rates because there is no such thing as a typical insulation contractor. The quote form asks for the state you are based in, what you install, your number of field employees and the coverage you want to talk about.

Ohio: what the state sets for insulation work, what each rule leaves open, and the coverage page that discusses it.
Contractor license The state licensing agency’s own list names no insulation category; it is written for commercial contractors
Injury and damage to others from the work, during the job and after it General Liability
Energy code The Residential Code of Ohio and the Ohio Building Code, statewide
Damage the finished work causes after you leave General Liability
Workers’ compensation Bought from the state fund unless the employer qualifies to self-insure
A crew member hurt on the job

Where a state sets rules on who may do the work or what it must meet, the policies still decide who pays when something goes wrong.

  • Where a state sets a license, a registration or an energy code, it is a requirement of the state, not insurance.
  • In this state, workers’ comp comes from the state fund unless the employer qualifies to self-insure; we place the rest of your coverage.

A chart of what Ohio requires, in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. Contractor license: The state licensing agency’s own list names no insulation category; it is written for commercial contractors. It leaves open injury and damage to others from the work, during the job and after it, which General Liability answers. Energy code: The Residential Code of Ohio and the Ohio Building Code, statewide. It leaves open damage the finished work causes after you leave, which General Liability answers. Workers’ compensation: Bought from the state fund unless the employer qualifies to self-insure. No connector is drawn for this row. Notes: Where a state sets a license, a registration or an energy code, it is a requirement of the state, not insurance. In this state, workers’ comp comes from the state fund unless the employer qualifies to self-insure; we place the rest of your coverage. The conclusion reads: Where a state sets rules on who may do the work or what it must meet, the policies still decide who pays when something goes wrong. No figures are shown.

Ohio insulation contractor insurance questions

Ohio contractor license requirements: which trades does the Ohio Construction Industry Licensing Board license?

ORC 4740.01(D) defines a “Licensed trade” as “a trade performed by a heating, ventilating, and air conditioning contractor, a refrigeration contractor, an electrical contractor, a plumbing contractor, or a hydronics contractor.” That list names no insulation category. The board’s complaint form says it “licenses commercial contractors in five trades” and that “OCILB may not have authority over residential contractors.” Under ORC 4740.01(F), the chapter’s construction project leaves out “a residential building as defined in section 3781.06 of the Revised Code.”

Ohio home improvement license: what do Columbus and Cincinnati say about home improvement contractors?

Columbus says a contractor who wishes “to perform structural work on existing” dwellings of the kinds the city lists must be licensed as a City of Columbus home improvement contractor, and that applications “are reviewed by the Board of General and Home Improvement Contractors.” Cincinnati’s Department of Buildings & Inspections lists a “Home Improvement Contractor” category for contractors “involved in repair, remodeling, alteration, improvement, or addition to any building used as a private residence in one, two and three family structures.” Each rule belongs to its own city.

Is workers comp required in Ohio once a business has an employee in service regularly?

ORC 4123.01(B)(1)(b) makes an employer of every person, firm or private corporation that “has in service one or more employees or shared employees regularly in the same business or in or about the same establishment”, and says “All such employers are subject to this chapter.” Except as ORC 4123.35 otherwise provides, every private employer pays premium “into the state insurance fund”. The exception is self-insurance: under ORC 4123.35(B), an employer the administrator finds of sufficient financial ability may be granted “status as a self-insuring employer.”

Ohio workers comp exemption: what does the statute let sole proprietors and partners elect?

ORC 4123.01 lets a partnership or sole proprietorship elect to include as an employee “any member of such partnership, the owner of the sole proprietorship, the individual incorporated as a corporation, or the officers of the family farm corporation.” That election takes written notice to the bureau of workers’ compensation. Cincinnati’s registration FAQ says “Those sole proprietors and business entities with no employees that are not required by state law to carry OBWC coverage will not be required to provide proof of coverage at the time of registration.”

Ohio energy code: which codes govern insulation on houses and on other buildings?

ORC 3781.10 has the board of building standards “incorporate those rules into separate residential and nonresidential building codes”, and says “The standards shall relate to the conservation of energy and the safety and sanitation of those buildings.” The Residential Code of Ohio’s energy chapter lists the International Energy Conservation Code among its compliance options. The Ohio Building Code’s energy chapter has buildings follow the International Energy Conservation Code or ASHRAE 90.1, except as modified in the chapter’s own sections; its referenced-standards rule, OAC 4101:1-35-01, lists IECC - 21 and 90.1-19.

Ohio residential energy code: which dwellings does the Residential Code of Ohio reach?

Section 101.2 of OAC 4101:8-1-01 says “The provisions of the "Residential Code of Ohio for One-, Two-, and Three-Family Dwellings" shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal, and demolition of every one-, two-, or three-family dwelling”. The code’s energy chapter, OAC 4101:8-11-01, says “Compliance shall be demonstrated by meeting the requirements of one of the following options:” and lists among them “The "International Energy Conservation Code."” The code’s referenced-standards rule, OAC 4101:8-44-01, lists “IECC—18: International Energy Conservation Code”.

Ohio insulation requirements: what must an installer certify under the Residential Code of Ohio?

Under section 1101.10.1 of the Residential Code of Ohio, an R-value identification mark is applied by the manufacturer to each piece of building thermal envelope insulation that is at or above a width the section states. “Alternatively, the insulation installers shall provide a certification that indicates the type, manufacturer and R-value of insulation installed in each element of” the building thermal envelope. For blown-in or sprayed fiberglass and cellulose, the certification also shows “the initial installed thickness, settled thickness, settled R-value, installed density, coverage area and number of bags installed”. Of the certification as a whole, the section says “The insulation installer shall sign, date and post the certification in a conspicuous location on the job site.”

Spray foam insulation Ohio: what goes on the certification, and what do federal agencies say?

Section 1101.10.1 of the Residential Code of Ohio says “For sprayed polyurethane foam (SPF) insulation, the installed thickness of the areas covered and the R-value of the installed thickness shall be indicated on the certification.” The U.S. Consumer Product Safety Commission’s fact sheet says the products it describes “contain isocyanates in Side A” and that “Homeowners should discuss safety protocols with their contractor and vacate the premises during and after installation”. The EPA calls its spray foam checklist “a voluntary aid to protect against potential risks from SPF”.

This page describes insurance for insulation contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, workers’ compensation and energy-code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Ohio insulation work

Tell us where your Ohio insulation business is based, what your crews install, how many field employees you carry and which lines beyond workers’ compensation you want to talk about.

Get a Quote Call 317-942-0549