An insulation installer job description names the work, the conditions and the training, and it leads to the hiring choice between employee and subcontractor. O*NET OnLine describes the occupation’s work as “Line and cover structures with insulating materials. May work with batt, roll, or blown insulation materials.” This guide turns that into a posting and a hire.
Duties to write into the posting
Start the description with the tasks, in plain verbs. Among the occupation’s tasks, O*NET lists “Measure and cut insulation for covering surfaces, using tape measures, handsaws, power saws, knives, or scissors.” Its task list includes “Fit, wrap, staple, or glue insulating materials to structures or surfaces, using hand tools or wires.”
Blown-in crews have tasks of their own, and a posting for that work should name them. O*NET also lists “Fill blower hoppers with insulating materials.” and “Move controls, buttons, or levers to start blowers and regulate flow of materials through nozzles.”
Some duties sit outside the install itself. O*NET lists “Remove old insulation, such as asbestos, following safety procedures.” If tear-out is part of the role, say so in the posting and say which procedures the crew follows.
Titles that fit the role, and work that belongs elsewhere
Pick a title that matches the work you will assign. O*NET’s sample of reported job titles for the occupation reads “Attic Blower, Insulation Estimator, Insulation Installer, Insulation Mechanic, Insulation Worker, Insulator, Retrofit Installer, Spray Foam Installer, Warehouse Insulation Worker”. Pipe and duct work is a different occupation. O*NET treats mechanical insulation as a separate occupation, whose workers “Apply insulating materials to pipes or ductwork, or other mechanical systems in order to help control and maintain temperature.” If your crews do building insulation and mechanical work, write a description for each role rather than blending them, so each posting says plainly what that worker does. Batt and blown-in crews have their own insurance page, fiberglass insulation contractor insurance, and rig crews have theirs, spray foam insurance.
Physical demands an applicant should see up front
State the physical side plainly, so applicants can judge it before they apply. O*NET’s work activities for the occupation include “Performing General Physical Activities”, which it describes as activities “such as climbing, lifting, balancing, walking, stooping, and handling materials.” Among the abilities O*NET lists for the occupation is “Stamina — The ability to exert yourself physically over long periods of time without getting winded or out of breath.”
The setting belongs in the posting as well. O*NET’s work context items for the occupation include “Exposed to Cramped Work Space, Awkward Positions”, “Exposed to High Places”, “Exposed to Contaminants” and “Indoors, Not Environmentally Controlled”. Its work context items also include “Wear Specialized Protective or Safety Equipment such as Breathing Apparatus, Safety Harness, Full Protection Suits, or Radiation Protection”. Heights deserve their line in the posting: NIOSH says “Falls are the number one cause of construction worker fatalities.”
Attic heat and the employer’s side of heat stress
Heat belongs in the posting and in the training plan. ENERGY STAR’s attic tips, written for do-it-yourself homeowners, say “During hot weather start working early, as attics heat up as the day moves on.” NIOSH says “Occupational heat stress is the combination of metabolic heat, environmental heat, and clothing and personal protective equipment (PPE), which results in increased heat storage within the body.”
NIOSH’s risk factors for heat-related illness include “indoor radiant heat sources”, “personal protective equipment (PPE) and clothing” and “previous heat-related illness”. NIOSH says “Heat stress can result in heat-related illnesses, such as heat stroke, heat exhaustion, rhabdomyolysis, heat cramps, and heat rashes.”
NIOSH writes its heat recommendations for employers. They say “Employers should ensure that workers are acclimatized before they work in a hot environment.” NIOSH recommends that employers “Assign new and unacclimatized workers lighter work and longer, more frequent rest periods.” Its work practice recommendations include “Use a buddy system where workers observe each other for signs of heat-related illnesses.” For a new hire, that points to lighter assignments while the person acclimatizes and a partner who watches for symptoms.
What the posting says about fiberglass dust and isocyanates
Where the job uses fiberglass, the description should name it. For fibrous glass dust, the NIOSH Pocket Guide to Chemical Hazards lists the exposure routes as “inhalation, skin and/or eye contact” and the symptoms as “irritation eyes, skin, nose, throat; dyspnea (breathing difficulty)”. Its personal protection lines for fibrous glass dust read “Prevent skin contact” and “Prevent eye contact”.
For spray foam crews, the chemical hazard starts with isocyanates. EPA’s archived guidance calls isocyanates “SPF’s key ingredient”. NIOSH says “Isocyanates can also sensitize workers, making them subject to severe asthma attacks if they are exposed again.”, and adds “There is evidence that both respiratory and dermal exposures can lead to sensitization.” EPA’s archived spray polyurethane foam guidance says “Exposures to SPF chemicals can cause asthma, sensitization, lung damage, other respiratory and breathing problems, and skin and eye irritation.”
NIOSH puts controls ahead of gear. It says “Engineering controls such as closed systems and ventilation should be the principal method for minimizing isocyanate exposure in the workplace.” NIOSH says other controls, “such as worker isolation and use of personal protective equipment such as respirators and personal protective clothing to prevent dermal exposures may also be necessary.” Our spray foam PPE guide goes through the respirators, suits and ventilation in detail.
Training to plan before the new hire starts work
Part of an installer’s training is a federal rule that falls on the employer. For construction work, OSHA’s hazard communication section reads “The requirements applicable to construction work under this section are identical to those set forth at § 1910.1200 of this chapter.” OSHA’s hazard communication standard says “Employers shall provide employees with effective information and training on hazardous chemicals in their work area at the time of their initial assignment, and whenever a new chemical hazard the employees have not previously been trained about is introduced into their work area.” It also says “Chemical-specific information must always be available through labels and safety data sheets.”
Respirator training has its own trigger. OSHA’s respirator section for construction reads “The requirements applicable to construction work under this section are identical to those set forth at 29 CFR 1910.134 of this chapter.” OSHA’s respiratory protection standard says “In any workplace where respirators are necessary to protect the health of the employee or whenever respirators are required by the employer, the employer shall establish and implement a written respiratory protection program with worksite-specific procedures.” The standard says “The employer shall provide the training prior to requiring the employee to use a respirator in the workplace.” Under the standard, the employer must ensure that each employee can demonstrate knowledge of items that include “How to inspect, put on and remove, use, and check the seals of the respirator”.
Heat training sits beside those rules as a NIOSH recommendation. NIOSH says “Employers should provide training to workers so they understand what heat stress is, how it affects their health and safety, and how it can be prevented.”
Certification and apprenticeship are a separate question from what the employer owes. O*NET names “Insulator (Thermal) (Existing Title: Insulation Worker)” among the occupation’s example apprenticeship titles and says “Specific title(s) listed above are vetted by industry and approved by the U.S. Department of Labor for use in a Registered Apprenticeship Program.” The programs themselves are in our installer certification guide, and whether a state license reaches the work is in our license guide.
Employee or subcontractor: the questions the IRS asks
For federal employment taxes, the IRS looks at the entire relationship between the business and the worker: the IRS says “It is critical that business owners correctly determine whether the individuals providing services are employees or independent contractors.” It states its general rule: “an individual is an independent contractor if the person for whom the services are performed has the right to control or direct only the result of the work and not what will be done and how it will be done.”
The IRS says “Facts that provide evidence of the degree of control and independence fall into three categories:” behavioral, financial and the type of relationship. Its behavioral question is “Does the company control or have the right to control what the worker does and how the worker does his or her job?” Its financial question is “Are the business aspects of the worker’s job controlled by the payer?”, which takes in things like “who provides tools/supplies”. On the type of relationship, the IRS asks “Will the relationship continue and is the work performed a key aspect of the business?”
Put those questions to the installer’s actual job: who sets the method and the schedule in the attic, who owns the blowing machine or the rig, and whether installing insulation is the work your business sells. The IRS says “no one factor stands alone in making this determination” and tells owners to “document each of the factors used in coming up with the determination.” It also says “If you classify an employee as an independent contractor and you have no reasonable basis for doing so, then you may be held liable for employment taxes for that worker”.
Wage-and-hour law asks its own version of the question. The U.S. Department of Labor says “Employers are responsible for determining whether a worker is an employee under the FLSA.” The Department says “Misclassification occurs when an employer treats a worker who is an employee under the FLSA as an independent contractor.”
Real-World Scenario: Ahead of the summer attic season, the owner of a cellulose crew wants to add an installer. She writes the posting from O*NET’s task list, adds the attic heat and the respirator her crew wears, and books hazard communication and respirator training before the new hire climbs into an attic. An applicant asks to come on as a subcontractor. She walks through the IRS questions, sees that she would set his schedule and methods and that he would run her blowing machine, concludes the facts point to an employee, and keeps her notes on each factor. Then she lets her insurance agent know the payroll has grown.
Wyoming’s workers’ compensation department on classifying the work
For a worker hurt on the job, the Department of Labor points to the state: “Individuals injured on the job while employed by private companies or state and local government agencies should contact their state workers’ compensation board.” The example below shows what a state says, under its own rules.
Wyoming’s Department of Workforce Services says “If your business is in an extra-hazardous industry, Workers’ Compensation coverage through DWS is required before work begins in Wyoming.” It says that for such a business, “Coverage is based on your business activity and determined using the North American Industry Classification System (NAICS).”, and “Classifications and the rates tied to them are determined after your employer registration is submitted through WYUI.wyo.gov.” The Wyoming page has the state’s own rules.
The job description is where you have already written down what the business does. If installers also handle tear-out, mechanical work or anything else, describe it accurately when you ask for coverage. The workers’ compensation page walks through how the policy’s classes, the payroll behind them and the audit after the term fit together.
Putting the posting together
Assemble the posting from the sections above, in this order:
- The duties, in O*NET’s plain verbs, for the work this role does: batts, blown-in, spray foam, tear-out.
- The conditions: attic heat, cramped spaces, heights, fiberglass dust or isocyanates, and the protective equipment the crew wears.
- The training you will give before the hire starts work: hazard communication, respirator training where respirators are required, and heat stress.
- The status of the role, decided on the facts, using the IRS’s questions for federal employment taxes, with your notes on each factor kept on file.
When you add installers or bring on a subcontracted crew, describe the work and the states where crews go in the quote request. The coverage side is workers’ compensation, with general liability for the work done at customers’ buildings, and insulation business insurance lists the other policies a crew carries.