States we serve

New Mexico Insulation Contractor Insurance

New Mexico’s Construction Industries Division lists “Acoustical insulation and insulation” among its specialty license classifications, and § 60-13-12(A) bars acting as a contractor without a license “classified to cover the type of work to be undertaken.” For employers in work the Construction Industries Licensing Act licenses, § 52-1-6(A) applies the Workers’ Compensation Act “regardless of the number of employees.”

Get a Quote Call 317-942-0549

A worker in a hard hat, safety glasses and dust mask lifting a fiberglass batt from stacked rolls in an attic — insulation contractor insurance in New Mexico

In New Mexico, § 60-13-12(A) says “No person shall act as a contractor without a license issued by the division classified to cover the type of work to be undertaken.”, and the Construction Industries Division’s classification rule lists “Acoustical insulation and insulation” among its general specialty license classifications. For employers in activities the Construction Industries Licensing Act requires to be licensed, § 52-1-6(A) applies the Workers’ Compensation Act “regardless of the number of employees.” Below: the classification and its exclusions, workers’ compensation, the energy codes, the federal entries on fiberglass and spray foam work, NM OSHA and local offices, ending with Rio Rancho’s out-of-city business registration packet and its request for “a copy of your liability insurance” “for applicable businesses”.

The Construction Industries Division’s “Acoustical insulation and insulation” classification and § 60-13-12(A)

Rule 14.6.6 NMAC names its issuing agency as “The Construction Industries Division (CID) of the Regulation and Licensing Department.” Its list of general specialty classifications, in section 14.6.6.9 NMAC, carries this entry: “GS-1. Acoustical insulation and insulation. Requires two years’ experience. Install any insulating material, including urethane foam and approved waterproof membranes and coatings, in or on buildings, structures and on piping for the purpose of energy conservation, temperature and sound control, and fireproofing. Does not include the installation of urethane roof systems.” Under § 60-13-12(A), the license must be “classified to cover the type of work to be undertaken”, and § 60-13-3 says the term contractor “includes subcontractor and specialty contractor”.

Section 14.6.6.8 NMAC limits each license: it “authorizes contracting only in the scope of work authorized by the classification(s) of the issued license”, and work outside that scope “constitutes a violation of the CILA and its rules and constitutes grounds for disciplinary action.” Under section 14.6.6.9 NMAC, the residential building classification “includes all work described by the GS specialty classifications, provided the work is limited to residential construction as defined under this provision.”

The handyman exclusion in § 60-13-3(D)(14), weatherization projects and the § 60-13-49 license bond

NMSA 1978 § 60-13-3(D)(14) takes out of the definition of contractor “an individual who works on one undertaking or project at a time that, in the aggregate or singly, does not exceed seven thousand two hundred dollars ($7,200) compensation a year, the work being casual, minor or inconsequential, such as handyman repairs; provided that this exemption shall not apply to any undertaking or project pertaining to the installation, connection or repair of electrical wiring, plumbing or gas fitting as defined in Section 60-13-32 NMSA 1978 and provided:” The provisos require that the work not be part of a larger or major operation, that the individual not advertise as qualified to contract, and that the individual “files annually with the division” a declaration. Section 60-13-3(D)(17) also excludes from the definition of contractor a weatherization project below the dollar figure the statute sets “that has been approved and is administered by a federal or state agency”.

Under § 60-13-49, no contractor’s license issues or renews until the applicant furnishes proof of responsibility, which is “a bond” in the amount the section sets, “underwritten by a corporate surety authorized to transact business in New Mexico.” Under § 60-13-49(B)(4), “failure to maintain the bond for the period required by law is cause for revocation of the license”.

Section 52-1-6(A) and employers in work the Construction Industries Licensing Act licenses

The Workers’ Compensation Act’s coverage section, NMSA 1978 § 52-1-6(A), reads: “The provisions of the Workers’ Compensation Act shall apply to employers of three or more workers; provided that act shall apply to all employers engaged in activities required to be licensed under the provisions of the Construction Industries Licensing Act [Chapter 60, Article 13 NMSA 1978] regardless of the number of employees.” The Workers’ Compensation Administration’s employer FAQ states the construction proviso on its own: “Employers actively engaging in activities required to be licensed by the Construction Industries Licensing Act must have workers’ compensation coverage, regardless of the number of employees.”

Under § 52-1-4(A), every employer subject to the act “shall direct his insurance carrier to file” evidence of coverage “in the form of a certificate” in the office of the director, and “The required certificate must be provided by an authorized insurer as defined in Section 59A-1-8 NMSA 1978.” An employer that shows the director “that he is financially solvent and that providing insurance coverage is unnecessary” receives the director’s certificate, filed in place of the certificate of insurance a workers’ compensation policy carries. Section 52-9-4 created a nonprofit, independent, public corporation “for the purpose of insuring employers against the risk of liability for payment of benefits claims to workers”, organized as a domestic mutual insurance company, and § 52-9-21 says it “shall not be considered a state agency for any purpose”.

On the licensing side, § 60-13-23 lists, among the causes for which a license “shall be revoked or suspended by the commission”, “failure to maintain workers’ compensation insurance as required by the Workers’ Compensation Act”. The Administration’s Uninsured Employers’ Fund “provides benefits such as indemnity and medical payments to injured workers when their employer does not have workers’ compensation insurance”.

Sole proprietor and executive employee elections under § 52-1-7, and the § 60-13-3.1 employee standard

Section 52-1-7 lets an executive employee of a corporation or limited liability company, “or a sole proprietor”, “affirmatively elect not to accept the provisions of the Workers’ Compensation Act” by filing an election with the director. The employer FAQ says a business owner is counted “if the business is engaged in activities required to be licensed by the Construction Industries Division (CID), although a CID sole proprietor has the option to exempt themselves.” The CID licensing page, for its part, states: “NOTE: Workers Compensation coverage is required for all licensed entities.”

For labor a contractor brings in, § 60-13-3.1(A), except as its Subsection D provides, says that within the construction industries a contractor who is an employer “shall consider a person providing labor or services to the contractor for compensation to be an employee of the contractor and not an independent contractor unless the following standards indicative of an independent contractor are met”.

Energy conservation rules 14.7.6 and 14.7.9 NMAC and the § 60-13-44(F) minimum for local codes

Rule 14.7.6 NMAC, the 2021 New Mexico Residential Energy Conservation Code, says “This rule adopts by reference the 2021 international energy conservation code (IECC), as amended by this rule.” Rule 14.7.9 NMAC, the 2021 New Mexico Commercial Energy Conservation Code, adopts the same model code “as amended by this rule.” Each reaches its own building type, residential or commercial contracting work performed in New Mexico on or after its effective date “that is subject to the jurisdiction of CID”, unless the work is under a permit applied for before that date. Each rule’s effective-date section reads “January 30, 2024 unless a later date is cited at the end of a section.”, and each states “After month July 30, 2024, permits may be issued only under this rule.”

Under § 60-13-44(F), codes adopted and approved under the Construction Industries Licensing Act “constitute a minimum requirement for the codes of political subdivisions.” The U.S. Department of Energy’s Building Energy Codes Program page for New Mexico, a federal listing and not the state’s adoption, prints “State Amendments Yes Yes” and “Enforcement Mandatory Statewide Mandatory Statewide”.

Thermal bypass checklists, the county testing list and the ceiling R-value change in rule 14.7.6 NMAC

A section the residential rule adds to the IECC says building envelope tightness and “insulation installation” are “field verified by the code official as part of the inspection process”, and “the builder or an energy rater may also field verify using the state of New Mexico acceptable processes.” The acceptable processes the rule names include the “construction industries division thermal bypass visual inspection checklist”, “a thermal bypass certification or checklist from a HERS rater”, “a build green NM checklist”, or an energy star program checklist from the state’s energy, minerals and natural resources department.

Citing “census rural urban mapping”, the residential energy rule requires compliance with its building thermal envelope, envelope testing and duct testing sections in “San Juan County, Sandoval County, Santa Fe County, Bernalillo County, Torrance County, and Dona Ana County.” The rule also amends the IECC’s insulation minimum R-value table, changing an entry in its ceiling R-value column for a climate zone the rule names.

Urethane foam inside the insulation scope, urethane roof systems outside it

For foam work, the insulation classification’s scope in section 14.6.6.9 NMAC covers “any insulating material, including urethane foam”, while “urethane roof systems” are excluded from it. The same section lists a classification to “Install, alter or repair roof systems on new or existing roof decks to create a weatherproof and waterproof protective membrane, with or without insulation,” using materials that include “urethane or any other approved materials”.

For a spray foam contractor and its client, the U.S. Environmental Protection Agency’s contractor-client checklist for spray polyurethane foam says it “was prepared as a voluntary aid to protect against potential risks from SPF; it is not a regulatory compliance tool”. Its topics for the client conversation include “why workers wear protective clothing and respiratory protection, why workers isolate the jobsite, and what to expect from cleanup procedures.” For any installer, including a fiberglass insulation contractor, the Federal Trade Commission’s 16 CFR 460.17 says “If you are an installer, you must give your customers a contract or receipt for the insulation you install.”

NM OSHA in the Environment Department and the State Plan’s military-base and tribal-land exceptions

The New Mexico Environment Department says “The Occupational Health and Safety Bureau (NM OSHA) is an agency within the New Mexico Environment Department.” OSHA’s New Mexico State Plan page says “The New Mexico State Plan applies to private sector workplaces in the state with the exception of” the areas it lists, among them “private sector establishments on military facilities and bases” and “tribal or private sector employment within any Indian reservation and lands under the control of a tribal government”, and that “Federal OSHA covers the issues not covered by the New Mexico State Plan.”

Albuquerque’s licensed-contractor permit rule, Rio Rancho’s liability insurance copy and Bernalillo County’s permit ordinance

For projects in the county’s own jurisdiction (its unincorporated areas, never Albuquerque city limits), Bernalillo County’s Building Services FAQ says all commercial projects must be done by a licensed contractor holding the state of New Mexico license classification it names, and “There is no specific requirement for an architect/engineer or licensed contractor on most residential projects.” Each card below gives what its own office says, for its own jurisdiction.

Albuquerque

The Building Safety Division’s Home Owner’s Building Permit Guide, which the city still serves, says “Any construction requiring a building permit also requires that a licensed contractor do the work, unless the owner-applicant performs the work.” The Planning Department’s Business License page says “All Business License applications and renewals require a current dated copy of the NM Taxation & Revenue Department Registration Certificate”.

Rio Rancho

The City of Rio Rancho Building Division says “Contractors performing work within the City’s limits are required to have a license with the State of New Mexico and an active business license with the City of Rio Rancho.” The city’s out-of-city business registration packet says “A copy of required State or Federal licensure and a copy of your liability insurance MUST be submitted with completed application (for applicable businesses).”

Santa Fe

The City of Santa Fe Land Use Department says “Building permits are required for most types of construction work within the city.” For new single-family homes, attached and detached, including guest houses, its Residential Green Building Code “requires a HERS (Home Energy Rating System) Index and a WERS (Water Efficiency Rating Score) rating completed by City-approved HERS and WERS raters.”

Hobbs

The City of Hobbs Building Safety & Permitting Services page says “The person responsible for the construction project must request each inspection.” The city’s business registration application asks for the “New Mexico Contractor’s License No.(if Applicable)” and warns “(If Business Is Located Outside City Limits, No Business Registration Will Be Issued.)”

Farmington

The City of Farmington’s Business Registration page says “City Code (Chapter 8) requires all persons engaging in business within the city limits to apply for and pay an annual business registration fee for each outlet, branch or location prior to engaging in business.” It adds: “Commercial locations inside the city limits must pass a fire inspection before a business registration is issued.”

Bernalillo County

For work in the county’s own jurisdiction, the Building Services FAQ of Bernalillo County Planning and Development Services says “It is a violation of county ordinance to not have a permit when work being done requires one.” It adds: “The individual doing the work covered by the permit must call for inspection prior to covering or concealing work.”

Sources: Albuquerque’s Home Owner’s Building Permit Guide, the Rio Rancho Building Division, the Santa Fe Land Use Department, Hobbs Building Safety & Permitting Services, Farmington Business Registration and the Bernalillo County Building Services FAQ.

The § 52-1-4(A) carrier filing, the CID coverage note and the Rio Rancho insurance copy

Under § 52-1-4(A), every employer subject to the act has its insurance carrier file the coverage certificate in the office of the director, unless the director has issued the employer the self-insurance certificate “filed in lieu of the certificate of insurance”; that insurance is the workers’ compensation line. The Construction Industries Division notes coverage “is required for all licensed entities”, though § 52-1-7 lets a sole proprietor elect out. Rio Rancho’s out-of-city business registration packet asks applicable businesses for “a copy of your liability insurance”; that line is general liability. For the rest of a program, see commercial auto, tools and equipment, umbrella liability and the insulation business insurance page.

Through Wexford Insurance, LLC, an independent insurance agency, Insulation Contractor Insurance places coverage for insulation contractors. Premium depends on payroll, the materials you spray or blow, subcontracted work, vehicles and rigs, tool and equipment values, and the states you work in. We do not publish typical rates because there is no such thing as a typical insulation contractor. Your number of field employees, what you install, the state you are based in and the coverage you want to talk about are what the quote form asks.

New Mexico: what the state sets for insulation work, what each rule leaves open, and the coverage page that discusses it.
Contractor license A state license or registration names insulation work; the law sets a threshold for when it applies
Injury and damage to others from the work, during the job and after it General Liability
Energy code The International Energy Conservation Code, statewide, for residential and commercial buildings
Damage the finished work causes after you leave General Liability
Workers’ compensation Required for covered employers, bought in the open market; the law sets a threshold for which employers it covers
A crew member hurt on the job Workers’ Compensation

Where a state sets rules on who may do the work or what it must meet, the policies still decide who pays when something goes wrong.

  • Where a state sets a license, a registration or an energy code, it is a requirement of the state, not insurance.

A chart of what New Mexico requires, in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. Contractor license: A state license or registration names insulation work; the law sets a threshold for when it applies. It leaves open injury and damage to others from the work, during the job and after it, which General Liability answers. Energy code: The International Energy Conservation Code, statewide, for residential and commercial buildings. It leaves open damage the finished work causes after you leave, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market; the law sets a threshold for which employers it covers. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: Where a state sets a license, a registration or an energy code, it is a requirement of the state, not insurance. The conclusion reads: Where a state sets rules on who may do the work or what it must meet, the policies still decide who pays when something goes wrong. No figures are shown.

Nearby states we also insure

New Mexico insulation contractor insurance questions

New Mexico contractor license requirements: which Construction Industries Division classification lists insulation?

Section 60-13-12(A) says “No person shall act as a contractor without a license issued by the division classified to cover the type of work to be undertaken.” Under § 60-13-3, contractor “includes subcontractor and specialty contractor”. The division’s classification rule lists this specialty entry: “GS-1. Acoustical insulation and insulation. Requires two years’ experience. Install any insulating material, including urethane foam and approved waterproof membranes and coatings, in or on buildings, structures and on piping for the purpose of energy conservation, temperature and sound control, and fireproofing. Does not include the installation of urethane roof systems.”

New Mexico contractor registration: what does CID ask of the business and its qualifying party?

The Construction Industries Division’s licensing page says “CID issues licenses to qualified business entities that employ or are owned by one or more Qualifying Parties (QP) who are validly certified by CID to perform the scope of work in which the licensee intends to engage.” It says “QP applicants must pass the exam(s) applicable to the classification being sought, as well as a Contractor’s Business and Law exam.” The page adds “The company must secure a license bond”, and the application carries a “Tax registration certificate from Tax and Revenue Department”.

Is workers comp required in New Mexico when the Construction Industries Division licenses the work?

Section 52-1-6(A) reads: “The provisions of the Workers’ Compensation Act shall apply to employers of three or more workers; provided that act shall apply to all employers engaged in activities required to be licensed under the provisions of the Construction Industries Licensing Act [Chapter 60, Article 13 NMSA 1978] regardless of the number of employees.” The Workers’ Compensation Administration’s employer FAQ puts the construction rule this way: “Employers actively engaging in activities required to be licensed by the Construction Industries Licensing Act must have workers’ compensation coverage, regardless of the number of employees.”

New Mexico workers compensation requirements: who files the certificate, and can a sole proprietor opt out?

Under § 52-1-4(A), every employer subject to the act “shall direct his insurance carrier to file, and the insurance carrier shall file, in the office of the director evidence of workers’ compensation insurance coverage in the form of a certificate”, unless the director has issued the employer a certificate “filed in lieu of the certificate of insurance”, and “The required certificate must be provided by an authorized insurer as defined in Section 59A-1-8 NMSA 1978.” Section 52-1-7 lets certain executive employees, “or a sole proprietor”, elect out by filing with the director.

New Mexico energy code: which rules govern insulation on houses and commercial buildings?

The 2021 New Mexico Residential Energy Conservation Code and the 2021 New Mexico Commercial Energy Conservation Code each adopt by reference the 2021 international energy conservation code (IECC) as amended, for residential or commercial work respectively, done in New Mexico on or after the effective date “that is subject to the jurisdiction of CID”, unless under a permit applied for before that date. Each rule’s effective-date section reads “January 30, 2024 unless a later date is cited at the end of a section.”, and each states “After month July 30, 2024, permits may be issued only under this rule.”

New Mexico residential energy code: how is insulation installation checked?

Rule 14.7.6 NMAC adds a section to the IECC saying building envelope tightness and “insulation installation” are “field verified by the code official as part of the inspection process”, and “the builder or an energy rater may also field verify using the state of New Mexico acceptable processes.” Those processes “include but are not limited to” the “construction industries division thermal bypass visual inspection checklist”, “a thermal bypass certification or checklist from a HERS rater” and “a build green NM checklist”.

Spray foam insulation New Mexico: where does urethane foam appear in the CID classification rule?

The division’s insulation classification, “Acoustical insulation and insulation”, has the scope to “Install any insulating material, including urethane foam and approved waterproof membranes and coatings, in or on buildings, structures and on piping for the purpose of energy conservation, temperature and sound control, and fireproofing.” It “Does not include the installation of urethane roof systems.” A roofing classification in the same rule covers roof systems “with or without insulation” using materials that include “urethane or any other approved materials”.

This page describes insurance for insulation contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, workers’ compensation and energy-code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your New Mexico insulation work

For insulation work based in New Mexico, the quote form asks where you are based, what you install, your field headcount and which coverage you want to talk through.

Get a Quote Call 317-942-0549