Owner Resources

Spray Foam Applicator Certification and Training

A worker in a hard hat standing in a pitched attic lined with yellow fiberglass batts, beside stacked rolls

Spray foam applicator certification is an industry credential held by the individual applicator, earned through programs such as SPFA’s. It is not OSHA training, which is a duty the employer owes its employees, and it is not the energy code’s certificate, which is paperwork for the job.

The Spray Polyurethane Foam Alliance’s certification levels

EPA’s contractor checklist names SPFA’s Professional Certification Program, CPI, ABAA, BPI and “individual SPF producers” as sources of SPF training. SPFA certifies individuals by level, in an insulation track and a roofing track. SPFA’s certification page lists individual certifications for insulation and for roofing, starting with the “SPF Assistant” and moving through the “SPF Insulation or Roofing Installer”, the “SPF Insulation or Roofing Master Installer” and the “SPF Insulation or Roofing Project Manager”. It says “The SPF Assistant certification is the first level for BOTH Insulation AND Roofing.”

The levels follow what a person does around the rig. SPFA says an assistant’s duties “may include assisting in equipment and job set-up, substrate preparation, material handling and staging, moving of hoses/scaffolding/ladders, masking, trimming, clean-up and other non-spraying tasks”, and adds “No experience required.” For the next level up, SPFA says “The SPF Installer has some experience in spraying foam with the guidance of a more experienced Master Installer or Project Manager.” Higher up, SPFA says its master installer “has demonstrated competence in SPF applications through a field examination.”, and its project manager’s duties may include “knowledge and skills in building science/design, material selection/estimating, and codes and standards compliance.” For the installer, master installer and project manager levels, SPFA’s page sets an experience threshold and says “You can start the certification process prior to having the experience but will only be fully certified once that threshold is achieved.”

Written exams, the field exam and the fees SPFA names

Each SPFA level runs through enrollment and a written exam, and the master installer level adds a field exam. SPFA’s first step for each level reads “Enroll in the program and register to take the exam (Enrollment has a one-time fee)”, and its page says the written exams can be taken “in person or remotely.” SPFA says “The written examinations shall provide documented proof of the candidate’s knowledge to be able to complete the tasks within their specific level of certification.”

Preparation is left to the candidate. Of its exam preparatory courses, SPFA says “The courses are not mandatory, but are strongly encouraged”, and it adds “Self-Study is also acceptable for those who have SPF experience.” Its exam page says “Each level builds on the lower levels”.

SPFA’s field exam page says the exam is “REQUIRED FOR MASTER INSTALLER LEVEL ONLY” and that “The Field Exam may take place on a real live jobsite or in a mock-up setting.” SPFA says the field examination provides proof of the master installer’s “ability to manufacture quality open and/or closed cell foam or roofing foam in place.” On money, SPFA names the charges without a number we would repeat: “The Field Exam fees include a paid Field Examiner and Exam processing fees.”, and candidates “will be charged the full examination fee for each examination session scheduled.”

Accrediting the company, not the applicator

SPFA’s program also accredits companies, and that credential sits on top of the individual ones. It says “The PCP Contractor Accreditation is a credential that validates your business as a whole.” The same page says “While Accreditation covers your operations, you still need certified individuals”.

The paperwork is where insurance meets the program. Among the documents its accreditation asks a company to submit, SPFA’s program lists “Proof of Business - Copy of License or Registration”, a “Certificate of Insurance” and “Annual Training (as required by OSHA standards)”. For an accredited company, it says “All SPF Field Personnel Must Be SPFA PCP Certified.” If you are working toward accreditation, line up a current certificate of insurance for your general liability and the rest of your spray foam insurance before you apply, and see our license guide for where the license or registration copy comes from in your state.

CPI’s free chemical health and safety training

The Center for the Polyurethanes Industry’s course is a safety course with a completion card, and CPI says it is free to the weatherization professionals, applicators and helpers it names. The American Chemistry Council’s Center for the Polyurethanes Industry (CPI) says its SPF training courses “are available free to weatherization professionals, SPF applicators and helpers who work with low-pressure and/or high-pressure spray polyurethane foam.” CPI’s training page says the training “provides information about the use, handling and disposal of SPF, potential health hazards and control measures, including engineering controls and personal protective equipment (PPE).”

Pick the course by the equipment the person will run. CPI describes a low-pressure course for those “who work with one component SPF or two component low-pressure SPF kits/systems for air sealing/insulating” and a high-pressure course for “SPF contractors, applicators or helpers who work with two component high-pressure SPF systems.”

On passing the course exam, a trainee can print a “Recognition of Completion” form and wallet card. CPI says “As your expiration date approaches, the system will remind you via email to renew your training.” Its training also “allows users to verify a worker’s training status by checking the individual’s unique system identification number that each person received upon completing the training.” The low-pressure course was produced under an OSHA grant, and its notice says “It does not necessarily reflect the views or policies of the U.S. Department of Labor”.

Supplier and manufacturer classes beside the association programs

Hands-on classes can also come from the people who sell you material. CPI’s page on selecting a contractor says “For a high-pressure product and some low-pressure products, many manufacturers offer or even require specialized contractor training.” CPI adds “Additional training and certification programs may be available through your material suppliers, distributors and other third parties like the Spray Polyurethane Foam Alliance.”

SPFA publishes a list of supplier members “who have training facilities for spray foam professionals”, and says “This list does not represent all Supplier Members with training facilities.” Ask your supplier what its class covers and what proof of completion it issues.

Real-World Scenario: A spray foam owner whose crew sprays closed-cell foam hires a helper who has no time yet near a rig. Before the helper handles any chemical, the owner enrolls him in CPI’s high-pressure course, gives him the respirator training the company’s program calls for, and starts him toward SPFA’s assistant level. When a builder asks for training proof with the bid, the owner sends the helper’s wallet card, the lead applicator’s SPFA certificate and a current certificate of insurance in the same email.

What EPA’s spray foam checklists ask a contractor to show

EPA’s spray foam checklists treat training cards as something a crew carries and shows, and they are voluntary. EPA’s contractor checklist says “This checklist was prepared as a voluntary aid to protect against potential risks from SPF; it is not a regulatory compliance tool.”, and adds “However, some of the best practices included in the checklist may be required under local, state or federal worker protection or other regulations.” It asks the contractor to “Ensure that all workers have completed the appropriate training for health and safety, equipment, and installation prior to beginning work on site and that they carry wallet-size cards to demonstrate that they have passed testing and certification requirements.” It also says “Maintain an on-site copy of the contractor’s written safety plan. Meet all OSHA, state, and local safety requirements for installers and for other workers.”

EPA’s customer guidance includes asking about training. EPA’s contractor-client communications checklist lists, among topics to discuss with the client, the “Training and certification credentials of the project manager, installers, and assistants.” EPA’s archived page on safer workplace practices tells building owners and occupants “Ensure your contractor has received appropriate training.” and “Verify the contractor’s insurance and licenses.” On its archived page of programs related to spray foam, EPA lists SPFA’s certification under “Related certification and training” and says “Each level requires passage of an extensive written exam before the candidate can move on to a higher level of certification.”

OSHA puts the training duty on the employer

The training OSHA’s rules require is a duty an employer owes its employees. The Occupational Safety and Health Act defines an employer as “a person engaged in a business affecting commerce who has employees”, and its section on employer duties says each employer “shall comply with occupational safety and health standards promulgated under this chapter.”

In OSHA’s construction rules, the safety training and education section says “The employer shall instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposure to illness or injury.”

Chemical and respirator training each have their own standard. OSHA’s construction rule on hazardous chemicals says its hazard communication requirements “are identical to those set forth at § 1910.1200 of this chapter.”, and the hazard communication standard itself says “Employers shall provide employees with effective information and training on hazardous chemicals in their work area at the time of their initial assignment, and whenever a new chemical hazard the employees have not previously been trained about is introduced into their work area.” For respirators, OSHA’s construction rule says “The requirements applicable to construction work under this section are identical to those set forth at 29 CFR 1910.134 of this chapter.” OSHA’s respiratory protection standard says “This paragraph requires the employer to provide effective training to employees who are required to use respirators.” and “The employer shall provide the training prior to requiring the employee to use a respirator in the workplace.” It says “Retraining shall be administered annually” and in the situations it lists.

EPA’s archived workplace page sums it up: “OSHA requires that workers be trained so that they are aware of the potential hazards and follow safe work practices.” Our spray foam PPE guide covers the respirator program itself, and our workers’ compensation page covers the policy that sits behind your employees.

A credential for the applicator, a certificate for the attic

An applicator certification describes the person; the insulation certificate a building office asks for describes the job. CPI says “Some jurisdictions may also require a small card called an insulation card to be posted after the job is completed.”, and that the card can carry “the contractor’s certification that the installation has been performed in accordance with local code requirements.” In Keene, New Hampshire, the city’s permit requirements for multifamily and commercial buildings say “Attic insulation must be completed and certificate of insulation displayed.” The New Hampshire page sets out Keene’s rule among the state’s local offices.

Where a building office asks for that certificate, the rule or code that asks for it sets the wording. The Ohio page and the New York page set out their states’ energy code text on what the installer certifies, including a line for spray foam. Where the code or the local office asks for the certificate, fill it in for the job, whatever cards your crew carries. Our installer certification guide covers the other certificates and receipts a job produces.

Where a contractor license names spray foam

A contractor license comes from a state or city office, and some licenses name spray foam in their scope. Nevada’s contractor regulations say “The Board will grant to qualified applicants a license in the specialty of installing and applying polyurethane or other similar products and coatings, whether in spray or rigid form, for the thermal insulation of structures”. The Nevada rules also list an insulation subclassification under roofing and siding, for “The installation of glass, metal, plastic, urethane and other material used for the insulation of buildings.” Those quoted lines leave open which classification fits a particular job, so read the Nevada page before you bid there.

In Casper, Wyoming, the city’s Insulation Contractor license “authorizes the contractor to sub-contract under a Class I, Class IIA, Class IIB, or Class III general contractor to carry on or engage in the business of insulation construction to include batt, spray foam, blow-in, or any other form of insulation material and/or method in residential and commercial buildings.” Casper’s license comes from the city, not the state, and the Wyoming page sets it out. Keep a program certificate and a license as separate lines on your checklist.

Keeping cards, certificates and policy papers current

A training program only helps you if the proof is current and you can find it when a builder asks. A working order for an owner:

  • Enroll each new helper in the CPI course that matches the equipment, and keep the identification number CPI issues so a customer can check the person’s training status.
  • Put renewal dates on the calendar: CPI emails a reminder as a recognition nears expiration, and OSHA’s respirator standard says “Retraining shall be administered annually”.
  • Decide which SPFA level each sprayer is working toward, and read the experience threshold on SPFA’s page before you schedule the exam.
  • Keep the wallet cards with the crew, as EPA’s checklist asks.
  • Be ready when a customer asks, as CPI suggests, “Is the certification current? Is the training recent, or has it been refreshed?”
  • Keep a current certificate of insurance on hand. CPI tells customers “You can ask for proof of insurance from your contractor, which is generally in the form of a certificate of insurance.”

Before you send the quote form, list who sprays, who helps and what training each person holds, so the application describes the crew as it actually works.

Spray foam credentials side by side: who issues each, and whether it attaches to a person, a company or a job

A comparison of spray foam credentials in groups. Industry programs: the association’s applicator certification by level, the chemical health and safety course completion, company accreditation, and supplier or manufacturer training. Government rules and codes: the employer’s training duty under OSHA, the installer’s certificate on the job where a local office asks for it, and a state or city contractor license. No figures are shown.

Frequently asked questions

Spray foam applicator certification: who issues it?

Industry programs provide the training and certification. EPA’s contractor checklist says “SPF training is provided by the Spray Polyurethane Foam Association (SPFA) Professional Certification Program, the Center for Polyurethanes Industry (CPI), Air Barrier Association of America (ABAA), Building Performance Institute (BPI), and individual SPF producers.” SPFA’s program lists individual certifications for insulation and for roofing, starting with the “SPF Assistant”. EPA says its checklist “was prepared as a voluntary aid to protect against potential risks from SPF; it is not a regulatory compliance tool.”

Spray foam applicator license: is it the same as a certification?

No. A license comes from a state or local office, and a certification comes from a program. Nevada’s contractor regulations say the Board “will grant to qualified applicants a license in the specialty of installing and applying polyurethane or other similar products and coatings, whether in spray or rigid form, for the thermal insulation of structures”, while SPFA sets its own certification levels and exams. Whether your state licenses the work at all is answered on that state’s page.

How to get certified for spray foam insulation, step by step?

With SPFA, every level starts the same way: “Enroll in the program and register to take the exam (Enrollment has a one-time fee)”. The written exams can be taken “in person or remotely.”, and SPFA says its preparatory courses “are not mandatory, but are strongly encouraged”. The master installer level adds a field exam. SPFA’s installer and higher levels carry an experience threshold, and SPFA says “You can start the certification process prior to having the experience but will only be fully certified once that threshold is achieved.”

Spray foam certification online: can the exams and training be done remotely?

Parts of it can. SPFA says its written exams can be taken “in person or remotely.” CPI’s foam safety training is an online course, and CPI tells trainees “Complete the training lessons on your own schedule.” The master installer field exam is different: SPFA says “The Field Exam may take place on a real live jobsite or in a mock-up setting.” Plan for that hands-on step when you map out a crew member’s path.

Spray foam certification cost: what do you pay for?

This guide gives no figure; the programs describe their own charges. SPFA says enrollment “has a one-time fee”, that candidates “will be charged the full examination fee for each examination session scheduled”, and that “The Field Exam fees include a paid Field Examiner and Exam processing fees.” CPI says its health and safety courses “are available free to weatherization professionals, SPF applicators and helpers who work with low-pressure and/or high-pressure spray polyurethane foam.” Count the crew time each step takes as well.

Spray foam training courses: what does the free CPI course cover?

CPI says its free foam safety course “provides information about the use, handling and disposal of SPF, potential health hazards and control measures, including engineering controls and personal protective equipment (PPE).” It offers a low-pressure course and a high-pressure course, the high-pressure course being for “SPF contractors, applicators or helpers who work with two component high-pressure SPF systems.” A trainee who passes can print a “Recognition of Completion” form and wallet card, and CPI sends a reminder before it expires.

Foam applicator requirements: what does OSHA require of the employer?

OSHA’s rules bind employers as to their employees. Its construction safety training rule says “The employer shall instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposure to illness or injury.” The hazard communication standard calls for effective information and training on hazardous chemicals, and its respiratory protection standard says “The employer shall provide the training prior to requiring the employee to use a respirator in the workplace.”