Owner Resources

Residential Insulation Inspection Checklist for Code Day

An applicator in a coverall and respirator spraying white foam insulation onto the underside of a roof deck

The energy code that applies on code day depends on where the house sits: in Kansas local governments adopt the code, and in Kentucky local government decides whether single-family homes are inspected. The list below takes job-site items from the Department of Energy’s weatherization job aids and the FTC’s home insulation rule, and state rules from the states’ own sources.

Start with the energy code your job falls under

Before anyone climbs into the attic, the crew needs the name of the code. The state, or the local government, picks it. In Massachusetts, the Department of Energy Resources says “The Base Code is IECC 2021 with MA amendments: 780 CMR Chapter 11R (residential) and 780 CMR Chapter 13 (commercial).” It adds, “Municipalities may choose to adopt the Stretch Code in lieu of the Base Energy Code.” A crew working in that state needs the town as well as the state before it knows which code an inspector reads from, and the Massachusetts page sets out the Base Code and the Stretch Code.

Idaho runs the other way. Its energy code statute bars local governments from adopting energy requirements “that differ from or are more extensive than the requirements of the Idaho energy conservation code as provided for in this chapter.” The same statute says it does not apply to the code’s administrative chapter “with respect to the administrative processes of any city, county, incorporated or unincorporated area, special use district, or any other local governmental entity.” The Idaho page quotes the adopting rule and its amendments.

For residential work, Kansas leaves the choice to cities and counties. The Kansas Corporation Commission says “Because Kansas is a home rule state, the responsibility for adoption and enforcement of building energy codes lies with local jurisdictions.” On a Kansas job, the Kansas page is a starting point, and the city or county building office is where the answer for the address lives. Who pulls the permit for the job is its own question, covered in our permit guide.

Whether an inspector sees the work at all

Some state rules leave the inspection itself to local government. Kentucky’s building code statute provides “that permits, inspections, and certificates of occupancy shall not be mandatory for single-family residences unless a local government passes an ordinance requiring inspections of single-family residences.” That line is about permits and inspections, not about which code applies; the Kentucky page quotes the codes the state lists as adopted.

The scope of a state’s energy rules can also leave an existing house out. Iowa’s rules say “Any construction of buildings or facilities that are intended for human occupancy and that are heated or cooled is covered, with the exception of renovation and remodeling of residential buildings of one or two dwelling units, which are not covered.” A retrofit crew in Iowa should read the Iowa page before telling a homeowner what the code asks of an attic job.

New homes can sit squarely inside a state code. Montana’s Department of Environmental Quality says “Montana has a state-wide energy code that governs all new home construction.”

Air sealing comes before the first bag

Seal first, then insulate. The job aids below are weatherization-program training material, not a code; the adopted code decides what an inspector reads. The Department of Energy’s job aid for preparing an attic floor says “Ensure air sealing work is complete prior to adding insulation.” Its list also says “Seal holes between the attic and the outside.” and “Duct ventilation fans to the outside.”

The air sealing job aid for attic top plates names the goal: “Holes, penetrations, chases, cracks, gaps, and joints sealed to prevent air leakage and moisture movement between the attic and conditioned space”. Its job site requirements include “Existing insulation was removed as needed to access air sealing locations.” The Massachusetts Base Code’s residential chapter, which applies unless the town has adopted an opt-in code, rewrites the code’s table of air barrier and insulation installation requirements to read “All insulation shall be installed at Grade I quality in accordance with ICC/RESNET 301.” and “Air-permeable insulation shall not be used as a sealing material.”

Depth rulers, coverage and the attic floor

Get the attic floor ready so that the depth of what goes in can be checked against rulers. The attic-floor job aid starts with access: “Remove stored or miscellaneous materials that would prevent insulation from being installed level and in contact with the attic floor.” It then lists “Cover all wiring junction boxes and flag to be visible above final insulation levels.”, “Install soffit vent baffles at all vented soffits.” and “Install dams around attic access, mechanical equipment, and flues/chimneys.” On height, it says “The damming should be higher than the finished depth of any new insulation. Note that the clearance distance from damming to insulation can vary; follow guidance from the authority having jurisdiction.”

Depth needs a marker anyone can read without wading in. The same job aid shows “Insulation depth rulers installed” among its steps, at the spacing it sets out.

The unfloored-attic job aid covers the blowing itself. Before starting, it says “Verify against work order that correct insulation material is being installed.” and “Verify insulation depth/density against manufacturer’s coverage chart.” During the job: “While installing, regularly check depth of insulation for even coverage and to meet required depth.” Its post-installation check lists “Insulation blown to proper depth.”, “Level and even coverage reaches to all edges.”, “Insulation is not blown onto equipment or between dams and the items dams are protecting.” and “Insulation has no gaps, voids, compression, or misalignment.” Where there is storage decking, it adds “When insulating attic platforms or attics with partial platforms, insulation is in contact with air barrier (under platform) not blown over platform.”

Real-World Scenario: An attic job is wrapping up in a town whose building office inspects energy work. Ahead of the visit, the crew lead climbs up with the job aid’s checklist, confirms the rulers are in place and read clearly, checks that the flagged junction boxes stand above the new layer, and looks along the eaves for baffles and full coverage. Back downstairs, she fills out the certificate, posts it by the attic entrance and hands the homeowner a signed receipt.

The attic hatch and its dam

The hatch is where the attic meets the living space, so treat it as part of the job, not trim. The Department of Energy’s attic hatch job aid explains why: “Uninsulated and unsealed attic access points allow conditioned air to escape the home in all seasons and reduce the overall R-value of the attic.”

Its checklist items run as follows. “Insulate hatch to proper R-value (the maximum R-value structurally allowable, up to the final insulation level of surrounding attic).” “Durably attach insulation to hatch.” “Weatherstrip or otherwise treat access to prevent air movement when hatch is closed.” “Ensure access closes with a tight fit or latch.” It ends with “Verify air-tightness of hatch when closed with blower door and smoke (or infrared, if temperatures permit).”

A state can write the hatch into its code. Virginia’s amendment to the access hatch section says “Access doors from conditioned spaces to unconditioned spaces (e.g., attics and crawl spaces) shall be weatherstripped and insulated in accordance with the following values:”, and the values follow in the state’s own text. The Virginia page sets out the state’s energy rules.

Walls, knee walls and spray foam in the job aids

Knee walls get the same order: seal, then fill, then write it down. In the Department of Energy’s job aid for a knee wall insulated with two-part spray foam, the air sealing items sit under the heading “(check prior to insulation)”, and the insulation list starts with “Install insulation to manufacturer’s specifications/ proper density.” The same job aid draws a line between a utility attic and a storage attic: “if the attic is only used for the service of utilities, foam will be separated from the attic space using a suitable ignition barrier. If the attic space is used for storage or occupancy, spray foam will be separated from the attic using a suitable thermal barrier.” Foam crews can read how that work is insured on our spray foam coverage page.

For dense-pack walls, the sidewall job aid says “Probe cavities to ensure all were accessed. Fill all cavities to proper density. (Verify before holes are plugged or with blower door and infrared scan if temperature permits.)” The knee wall and sidewall job aids each list the same certificate line: “Fill out applicable sections of house-wide insulation certificate with coverage area, thickness, and R-value.”

The certificate at the attic entrance and the customer’s receipt

The unfloored-attic job aid has the applicable sections of the house-wide insulation certificate filled out with “insulation type, coverage area, installed thickness, settled thickness, R-value, and number of bags installed”, and a footnote saying “Underlined details are required on all insulation certificates. Other items are required only when using blown-in insulation.” Its last picture says “When complete, post insulation certificate by attic entrance.” These job aids are training material: the unfloored-attic checklist is headed “Insulate attic floor and pass inspection the first time”, and its footer says the “job aids were funded by the Weatherization Assistance Program with contributions from the weatherization training network.” Ask the building office which certificate its adopted code asks for. Our installer certification guide sorts out a certificate on the wall from a certification for the crew.

The receipt is federal, and it goes to the customer whether or not anyone inspects. The FTC’s home insulation rule says “If you are an installer, you must give your customers a contract or receipt for the insulation you install.” For loose-fill, “the receipt must show the coverage area, initial installed thickness, minimum settled thickness, R-value, and the number of bags used.” Otherwise, apart from reflective insulation, “the receipt must show the coverage area, thickness, and R-value of the insulation you installed.” The rule adds “The receipt must be dated and signed by the installer.” and “To figure out the R-value of the insulation, use the data that the manufacturer gives you.” Our license guide explains why the receipt belongs to the job paperwork and not to the state’s licensing.

A state can add its own paper. Montana’s statute says that whoever starts the work on a new home “shall certify in writing to the building owner at the conclusion of construction that the residential building has been constructed in compliance with the energy-efficient construction standards”, subject to the exception it sets, and that “A person constructing a new residential building shall affix to that residential building in a manner prescribed by the department of labor and industry a labeling sticker”. The Montana page covers the certification and the sticker.

Testing, field verification and who signs off

Where the code calls for an air leakage test, the state may let a visual check stand in, or say who runs the test. Idaho’s amendments to the residential provisions say “A visual inspection shall be considered acceptable in lieu of testing when the items listed in Table R402.4.1.1, applicable to the method of construction, are field verified.”

Utah’s statewide amendments to the IECC put a signature on items “not readily visible during regularly scheduled inspections”: “Where required by the code official, the builder shall certify compliance with criteria indicated in Table R1102.4.1 for items which are not readily visible during regularly scheduled inspections.” They also say “The following parties shall be approved to conduct testing: Parties certified by BPI or RESNET, or licensed contractors who have completed training provided by Blower Door Test equipment manufacturers or other comparable training.” The Utah page gives the editions the state adopted. For an insulation crew, the practical point is that, where the code official requires it, the builder may certify work you did. Photographs of the air sealing before it is covered, and the certificate you filled out, give that person something to sign against.

A code-day sequence for your crew

Put the items above in the order the job runs:

  • Read the state page and call the building office for the address: which code, which edition, and whether it inspects this kind of job.
  • Seal the attic floor, the top plates and the penetrations, and build the dams, before any insulation goes in.
  • Clear the floor, flag the junction boxes, set the baffles and put the depth rulers in place.
  • Install to the manufacturer’s coverage chart, checking depth as you go, out to every edge.
  • Dam, insulate and weatherstrip the hatch so it closes tight.
  • Fill out the certificate, post it by the attic entrance, and give the customer the dated, signed receipt.

If a finished job later turns into a claim from the homeowner, the completed operations section of our general liability page explains how that coverage is read. To get a program priced, tell us the states and the work on the quote form.

Code day on a residential insulation job, from the adopted energy code to the paperwork left in the house

A flow of steps for code day. Start by finding the energy code the address falls under. Ask whether the local office inspects the work at all. Finish the air sealing and the dams before any insulation goes in. Install to the manufacturer’s coverage chart with depth rulers in place and even coverage to the edges. Treat the attic hatch so it is dammed, insulated and closes tight. End with the paperwork: the certificate posted by the attic entrance and a dated, signed receipt for the customer. No figures are shown.

Frequently asked questions

Residential insulation inspection checklist: what is on it?

It follows the energy code the job falls under, so start with the state page and the local building office. For the work itself, the Department of Energy’s weatherization job aids give a practical list: “Ensure air sealing work is complete prior to adding insulation.”, “Insulation depth rulers installed”, “Level and even coverage reaches to all edges.”, a dammed and weatherstripped hatch, and “When complete, post insulation certificate by attic entrance.” The FTC adds a dated, signed receipt for the customer.

Does insulation need to be inspected?

That depends on where the house sits. Kentucky’s building code statute provides “that permits, inspections, and certificates of occupancy shall not be mandatory for single-family residences unless a local government passes an ordinance requiring inspections of single-family residences.” The Kansas Corporation Commission says “Because Kansas is a home rule state, the responsibility for adoption and enforcement of building energy codes lies with local jurisdictions.” Ask the building office for the address before you schedule the work.

Insulation inspection requirements: who sets them?

The answer comes from the energy code adopted where the house sits and from the office that enforces it. Idaho’s statute bars local energy requirements “that differ from or are more extensive than the requirements of the Idaho energy conservation code as provided for in this chapter”, but sets aside the administrative processes of local governments. In Massachusetts, the Department of Energy Resources says “Municipalities may choose to adopt the Stretch Code in lieu of the Base Energy Code.” The Massachusetts and Idaho pages set out each state’s adopted code in the state’s own words.

What is an insulation inspection?

The code decides what is checked. Idaho’s amendments to the residential provisions say “A visual inspection shall be considered acceptable in lieu of testing when the items listed in Table R402.4.1.1, applicable to the method of construction, are field verified.” Utah’s statewide amendments add “Where required by the code official, the builder shall certify compliance with criteria indicated in Table R1102.4.1 for items which are not readily visible during regularly scheduled inspections.”

Insulation certificate: what does it list?

The Department of Energy’s unfloored-attic job aid has the applicable sections of the house-wide insulation certificate filled out with “insulation type, coverage area, installed thickness, settled thickness, R-value, and number of bags installed”, and a footnote saying “Underlined details are required on all insulation certificates. Other items are required only when using blown-in insulation.” It closes with “When complete, post insulation certificate by attic entrance.” That job aid is a weatherization program’s guide, so ask the building office what certificate its adopted code asks for.

Insulation inspection form or receipt: what must the installer hand over?

The FTC’s home insulation rule says “If you are an installer, you must give your customers a contract or receipt for the insulation you install.” For loose-fill, “the receipt must show the coverage area, initial installed thickness, minimum settled thickness, R-value, and the number of bags used.” The rule also says “For all insulation except loose-fill and reflective insulation, the receipt must show the coverage area, thickness, and R-value of the insulation you installed.” and “The receipt must be dated and signed by the installer.”

Does insulation need to be inspected in a remodel?

It turns on the state’s scope as well as the local office. Iowa’s energy rules say “Any construction of buildings or facilities that are intended for human occupancy and that are heated or cooled is covered, with the exception of renovation and remodeling of residential buildings of one or two dwelling units, which are not covered.” Read the state page for the house’s state and ask the building office before you tell a homeowner an attic job needs no inspection.